Updated November 2026
A duramont ergonomic office chair can support a healthier working posture, but only if it is adjusted to your body and your desk. This guide walks you through the setup in the order that matters most: seat height, seat depth, lumbar support, armrests, recline and tilt, and finally your desk layout. By the end, you will have a chair that fits your frame and a short checklist you can recheck every few months.
Before You Start: What You Need
You do not need special equipment, but a few simple tools make the process faster and more accurate. Most of the work is done by feel, so take your time and make small changes.
Shopping for one? See our guide: 7 Best Ergonomic Mesh Office Desk Chair Picks for Every Need (2026).
- A tape measure, for checking popliteal height and desk height
- A pair of shoes you normally wear to work, since heel height changes how your feet reach the floor
- A desk at a height you already use, or a plan to adjust it
- About 20 to 30 minutes, plus a second session a few days later to fine-tune
If you are still deciding between models or comparing features, you may find it useful to read Tralt Office Chair Ergonomic Desk Chair: Setup and Buying Guide (2026) alongside this guide, since many of the adjustment principles overlap.
Step 1: Set the Seat Height
Seat height is the foundation of the whole setup. The goal is to have your feet flat on the floor, or on a footrest, with your knees at roughly a right angle or slightly lower than your hips.
How to find the right height
- Sit all the way back in the chair so your spine is against the backrest.
- Raise or lower the seat until your thighs are parallel to the floor, or tilt very slightly downward toward the knees.
- Check that your feet are flat. If your toes barely touch the floor, the seat is too high. If your heels are lifted, it is too low.
- Leave a gap of about two to three finger widths between the front edge of the seat and the back of your knees. This keeps blood flow to the lower legs from being pinched.
If your feet still do not reach the floor at the height that suits your desk, use a footrest rather than letting the chair stay too high. A footrest is a legitimate solution, not a compromise.
Step 2: Adjust the Seat Depth
Seat depth controls how far the front edge of the cushion sits from the back of your knees. Many people skip this adjustment, and it is one of the most common sources of leg discomfort.
- With your back against the backrest, slide your hand between the front of the seat and the back of your knee.
- You should fit about two to four fingers. Less than that means the seat is too deep. More than that means the seat is too shallow and you will lose thigh support.
- If your chair has a sliding seat pan, adjust it now. If it does not, a lumbar cushion or a different seat cushion can sometimes help, though you should check the manufacturer’s guidance first.
Step 3: Position the Lumbar Support
Lumbar support fills the natural inward curve of your lower back. Without it, most people slump, and slumping shifts load onto the spinal discs and the muscles around them.
Finding the lumbar point
- Sit with your hips pushed back so your buttocks touch the rear of the seat.
- Locate the small hollow above your belt line and below your ribcage. This is where most people need support.
- Adjust the lumbar height, if your model offers it, so the support pad sits in that hollow.
- Adjust the depth of the lumbar pad so it provides gentle pressure without pushing you forward out of the seat.
If you have a history of back problems or ongoing pain, speak with a physical therapist or doctor before changing your support setup significantly.
Step 4: Set the Armrests
Armrests should support your forearms so your shoulders stay relaxed. Set them too high and your shoulders shrug. Set them too low and you lean sideways.
- Relax your shoulders completely.
- Bend your elbows to about 90 to 100 degrees.
- Adjust the armrest height so your forearms rest lightly on the pads without lifting your shoulders.
- Set the width so the pads sit close to your sides, not pushing your elbows outward.
Some people prefer to remove or lower the armrests when typing for long periods, since that allows the chair to slide closer to the desk. That is a valid choice as long as your wrists stay neutral.
Step 5: Tune the Recline and Tilt Tension
The recline mechanism lets you change your posture during the day, which matters more than most people realize. Staying in one fixed position for hours is tiring even when that position is good.
- Lean back and see whether the backrest supports you without forcing your head forward.
- Adjust the tilt tension so you can recline with light effort, but the chair does not tip back uncontrollably.
- If the chair has a lock, test it at two or three angles. Choose a comfortable angle for focused work and a more reclined one for reading or calls.
A useful rule is to keep your head balanced over your shoulders rather than pushed forward. If you find yourself craning toward the screen, move the monitor first, then revisit the recline.
Step 6: Arrange Your Desk and Screen Around the Chair
A chair cannot correct a poor desk layout on its own. Once the chair is set, arrange the surrounding elements so you do not have to reach, lean or hunch.
| Element | Target position |
|---|---|
| Keyboard height | Elbows at about 90 degrees, wrists neutral |
| Monitor top edge | At or slightly below eye level |
| Monitor distance | About an arm’s length away |
| Mouse position | Same level as the keyboard, close to your body |
| Feet | Flat on the floor or a footrest |
If the desk is too high for your chair, you may need a keyboard tray or a height-adjustable desk. For more on whether a sit-stand setup suits you, see Top 6 Ergonomic Standing Office Chairs for Long Workdays in 2026.
Step 7: Test, Then Refine Over One Week
Your first setup is a starting point, not a final answer. Give yourself a week of normal work before making the last adjustments.
- Day one: complete the steps above and work as usual.
- Days two and three: notice where discomfort appears. Note whether it is in the lower back, thighs, shoulders or wrists.
- Day four onward: make one change at a time, then wait a day before judging it.
- Recheck the seat height and armrests every few weeks, since fabric compression and daily use can subtly change how the chair feels.
Common Mistakes
- Sitting on the edge of the seat. This removes backrest support and encourages slouching. Slide back fully before adjusting anything.
- Setting armrests too high. Raised shoulders cause neck and upper back tension over time.
- Leaving the lumbar support at default. The default position rarely matches a specific body. Adjust it.
- Ignoring monitor height. A perfect chair with a low monitor still produces a forward head posture.
- Never moving. Even a well-adjusted chair works best when you change position every 30 to 60 minutes.
Tips for Getting More From Your Chair
- Recline briefly during phone calls or while reading. Changing angle is more important than finding one perfect angle.
- Keep both feet grounded. Crossing your legs for long periods can shift pelvis alignment.
- Stand up at least once an hour, even for a minute. A short walk resets posture more effectively than adjusting the chair again.
- If your chair seems to fit poorly despite careful setup, check whether it suits your height and weight range. Sizing guidance appears in Ergonomic Office Chair for Tall People: 7 Best Picks Compared (2026).
Recommended gear
Only a few accessories are worth considering, and most depend on your specific setup.
- A footrest helps when your feet do not reach the floor at a comfortable seat height. Look for one with a tilt angle and a non-slip surface. View on Amazon
- A keyboard tray can lower your keyboard when your desk is too high. View on Amazon
- A monitor riser raises the top of your screen to eye level without changing your desk. View on Amazon
FAQ
How do I know if my duramont ergonomic office chair is the right size?
Check whether you can sit with your back against the backrest, feet flat, and two to four fingers of space between the seat edge and the back of your knees. If you cannot reach those positions even after adjusting, the chair may not match your body dimensions.
Should my knees be higher or lower than my hips?
Ideally they should be level with your hips or slightly lower. This helps keep the pelvis tilted forward and supports the natural curve of the lower spine.
How often should I readjust the chair?
Check the setup when you first receive the chair, after a week of use, and then every few months. Readjust sooner if you change desks or start working differently.
Can I use a lumbar cushion instead of built-in support?
A separate cushion can help if the built-in support does not reach your lower back. Choose one that holds its shape and does not push you forward out of the seat.
Do armrests need to be used all the time?
No. Armrests are there to support your arms when needed. Many people use them for typing and remove or lower them for tasks that involve reaching or leaning.
How long should I sit before standing up?
Most ergonomic guidance suggests changing position at least every 30 to 60 minutes. Short standing breaks matter more than the exact interval.
When should I see a professional about my posture or pain?
If you have persistent pain, numbness, tingling or pain that wakes you at night, consult a doctor or physical therapist. Chair adjustments are helpful but do not replace medical assessment.
Conclusion
A well-set duramont ergonomic office chair starts with seat height, then moves through depth, lumbar support, armrests and recline. Once those are in place, arrange your desk and screen so your posture stays neutral. Recheck the setup after a week and again every few months, and keep moving throughout the day.

