Updated November 2026

Workout at your desk exercises are short movement sessions you can do without leaving your chair or workspace. A five-minute routine of seated and standing moves can loosen tight hips, wake up your legs, and interrupt long stretches of sitting. This guide shows you how to set up a simple routine and which moves to start with.

Set Up Your Routine Before You Start

Pick a fixed trigger, such as after every meeting or at the top of each hour, so you do not have to remember to move. Keep your feet flat on the floor, your screen at eye level, and your elbows near 90 degrees before you begin. Work within a range that feels comfortable, and stop any move that causes sharp pain.

Shopping for one? See our guide: 6 Best Standing Desk for Home Office (2026): Expert Picks.

Seated Moves for Your Upper Body and Core

Seated moves are the easiest to fit into a tight schedule because they need no floor space. Aim for 8 to 10 repetitions of each one, moving slowly.

  1. Seated shoulder rolls: Roll both shoulders backward in 10 slow circles, then reverse direction.
  2. Seated torso twists: Hold the armrests, rotate your upper body to one side, hold for 3 seconds, and switch sides.
  3. Chest openers: Clasp your hands behind your back, lift your chest, and hold for 15 to 20 seconds.

Standing and Lower-Body Moves

Standing up for a minute or two changes the load on your hips and lower back. Hold on to the desk for balance if needed.

  • Sit-to-stand squats: Stand up from your chair without using your hands, then sit back down slowly. Repeat 8 times.
  • Calf raises: Rise onto the balls of your feet, hold for 2 seconds, and lower. Do 15 repetitions.
  • Standing hip hinges: Push your hips back, keep your spine neutral, and return to standing. Repeat 8 times.
  • Marching in place: Lift each knee to about hip height for 45 seconds.

Build a Five-Minute Workout Sequence

A simple routine works well when you combine upper-body, core, and lower-body moves in a fixed order. The table below shows one sequence you can repeat at each break.

Time Move Target
0:00–1:00 Seated shoulder rolls Upper back
1:00–2:00 Seated torso twists Core and spine
2:00–3:00 Sit-to-stand squats Legs and hips
3:00–4:00 Calf raises Calves and circulation
4:00–5:00 Standing hip hinges Hamstrings and lower back

For more options, see Stretching Exercises While Sitting at Desk: 10 Moves for Stiff Workdays or Stand Up Desk Exercises: 9 Moves to Do Standing at Work.

A resistance band adds light tension to seated pulls and presses without taking up desk space. View on Amazon

A balance cushion or wobble board can turn standing calf raises into a small stability challenge. View on Amazon

Common Mistakes to Avoid

  • Rushing through reps. Slow, controlled movement gives your muscles more benefit in less time.
  • Holding your breath during twists or squats. Breathe steadily throughout each move.
  • Arching your lower back during hip hinges. Keep your spine long and your ribs stacked over your pelvis.
  • Skipping breaks because you feel busy. Two minutes of movement is better than none.

FAQ

How often should I do workout at your desk exercises?

Most desk workers find it practical to move once every hour. Even a two-minute session between tasks adds up over a full workday.

Do I need special equipment?

No. Your chair, desk, and wall are enough for the moves in this guide. A resistance band is optional and useful for variety.

What if I have a back or joint condition?

Consult a doctor or physical therapist before starting a new routine. They can tell you which moves suit your body and which to avoid.

Conclusion

Workout at your desk exercises fit into the gaps of a normal workday and help counter the stiffness of long hours of sitting. Start with the five-minute sequence above and repeat it at the same times each day. Over a few weeks, you can add reps or new moves as you feel ready.

Owen Palmer

About Owen Palmer

Owen Palmer is part of our editorial team and reviews and edits our fitness at work guides, checking product details against manufacturer specifications and owner feedback.